 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| New Product DG451/DG452/DG453 Vishay Siliconix High Voltage 4- Quad SPST CMOS Analog Switch DESCRIPTION The DG451 series has four independently selectable high voltage (44 V) SPST switches, each with a typical on resistance of 4 and a typical flatness of 0.2 , ideal parameters for low distortion audio signal switching. The DG451 (NC) and DG452 (NO) are identical except for the digital logic control input, which is inverted as shown in the Truth Table. The DG453 has two normally closed and two normally open switches. These are high voltage switches that are fully specified with dual supplies at 5 V and 15 V and a single supply of 12 V and operating with ultra low power dissipation (18 W). Fast switching speeds coupled with high signal bandwidth makes these parts suitable for video switching applications. All digital inputs have 0.8 V and 2.4 V logic thresholds ensuring low voltage TTL/CMOS compatibility. Each switch conducts equally well in both directions when on and can handle an input signal range that extends to the supply voltage rails. The DG451, DG452, and DG453 are pin compatible with the DG411, DG412, and DG413. FEATURES * * * * * * * * Low on-resistance (4 typical) On-resistance flatness (0.2 typical) 100 mA continuous current RoHS COMPLIANT 44 V supply maximum rating 15 V analog signal range Fully specified at supply voltages of 5 V, 12 V and 15 V Ultra low power dissipation of (18 W) Fast switching speed: - ton 80 ns - toff 60 ns * TTL/CMOS compatible * ESD protection 2 kV * Pin compatible with DG411, DG412, and DG413 APPLICATIONS * * * * * * * Audio and video signal switching Precision automatic test equipment Precision data acquisition Relay replacement Communications systems Automotive and avionics applications Sample and hold systems FUNCTIONAL BLOCK DIAGRAM AND PIN CONFIGURATION DG451 TSSOP16 and SOIC16 IN1 D1 S1 VGND S4 D4 IN4 1 2 3 4 5 6 7 8 Top View Top View 16 15 14 13 12 11 10 9 IN2 D2 S2 V+ VVL GND S3 D3 IN3 S4 D4 IN4 6 7 8 11 10 9 5 12 VL S3 D3 IN3 4 13 V+ DG453 TSSOP16 and SOIC16 IN1 D1 S1 1 2 3 16 15 14 IN2 D2 S2 TRUTH TABLE Logic 0 1 DG451 ON OFF DG452 OFF ON TRUTH TABLE Logic 0 1 SW1, SW4 OFF ON SW2, SW3 ON OFF Document Number: 74470 S-81306-Rev. D, 09-Jun-08 www.vishay.com 1 New Product DG451/DG452/DG453 Vishay Siliconix ORDERING INFORMATION Temp Range DG451/DG452/DG453 16-Pin TSSOP - 40 C to 125 Ca 16-Pin Narrow SOIC Notes: a. - 40 to 85 C datasheet limits apply. DG451EQ-T1-E3 DG452EQ-T1-E3 DG453EQ-T1-E3 DG451EY-T1-E3 DG452EY-T1-E3 DG453EY-T1-E3 Package Part Number ABSOLUTE MAXIMUM RATINGS TA = 25 C, unless otherwise noted Parameter V+ to VGND to VVL Digital Inputsa, VS, VD Continuous Current (Any Terminal) Peak Current, S or D (Pulsed 1 ms, 10 % Duty Cycle) Storage Temperature Power Dissipation (Package)b Thermal Resistance (Package)b ESD (HBM) 16-Pin TSSOPc 16-Pin Narrow SOICd 16-Pin TSSOP 16-Pin Narrow SOIC Limit 44 25 (GND - 0.3) to (V+) + 0.3 (V-) - 2 to (V+) + 2 or 30 mA, whichever occurs first 100 300 - 65 to 150 450 600 178 125 2 mA C mW C/W kV V Unit Notes: a. Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. b. All leads welded or soldered to PC board. c. Derate 5.6 mW/C above 70 C. d. Derate 8.0 mW/C above 75 C. SPECIFICATIONS FOR DUAL SUPPLIES Test Conditions Unless Specified V+ = 15 V, V- = - 15 V VL = 5 V, VIN = 2.4 V, 0.8 Va - 40 to 125 C Temp.b Full IS = - 10 mA, VD = - 10 V to + 10 V IS = - 10 mA, VD = 10 V Room Full Room Full Room Full Room Full Room Full Room Full 3.8 0.12 0.25 0.1 0.1 0.1 - 0.5 - 20 - 0.5 - 20 - 0.4 - 40 Typ.c Min.d - 15 Max.d 15 5.3 8.3 0.5 1 0.5 0.5 0.5 20 0.5 20 0.4 40 - 0.5 - 2.5 - 0.5 - 2.5 -1 -5 - 40 to 85 C Min.d - 15 Max.d 15 5.3 7.3 0.5 0.5 0.5 0.5 0.5 2.5 0.5 2.5 1 5 nA Unit V Parameter Analog Switch Analog Signal Rangee On-Resistance On-Resistance Match On-Resistance Flatness Switch Off Leakage Current Channel On Leakage Current Symbol VANALOG RON RON RFLATNESS IS = - 10 mA, VD = - 5 V, 0 V, + 5 V IS(off) VD = 10 V, VS = 10 V ID(off) ID(on) VS = VD = 10 V www.vishay.com 2 Document Number: 74470 S-81306-Rev. D, 09-Jun-08 New Product DG451/DG452/DG453 Vishay Siliconix SPECIFICATIONS FOR DUAL SUPPLIES Test Conditions Unless Specified V+ = 15 V, V- = - 15 V VL = 5 V, VIN = 2.4 V, 0.8 Va VIN Under Test = 0.8 V VIN Under Test = 2.4 V f = 1 MHz - 40 to 125 C Temp.b Full Full Room Room Full Room Full Room Room Room Room Room f = 1 MHz Room Room Signal = 5 VRMS, 20 Hz to 20 kHz, RL = 600 Room Typ.c 0.005 0.005 7 88 69 118 160 97 120 118 144 97 112 ns Min.d - 0.5 - 0.5 Max.d 0.5 0.5 - 40 to 85 C Min.d - 0.5 - 0.5 Max.d 0.5 0.5 Unit Parameter Digital Control Input Current, VIN Low Input Current, VIN High Input Capacitancee Dynamic Characteristics Turn-On Time Turn-Off Time Break-Before-Make Time Delay Charge Injectione Off Isolation e Symbol IIL IIH CIN A pF tON tOFF tD Q OIRR XTALK CS(off) CD(off) CD(on) THD RL = 300 , CL = 35 pF VS = 10 V, See Figure 2 DG453 only, VS = 10 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF RL = 50 , CL = 5 pF f = 1 MHz 18 22 - 60 - 85 31 34 103 0.04 % pF dB pC Channel-to-Channel Crosstalke Source Off Capacitancee Drain Off Capacitance Channel On Capacitancee Total Harmonic Distortione Power Supplies Power Supply Current Negative Supply Current Logic Supply Current Ground Current e I+ IIL IGND V+ = 16.5 V, V- = - 16.5 V VL = 5 V, VIN = 0 or 5 V Room Full Room Full Room Full Room Full 0.001 - 0.001 0.001 - 0.001 - 0.5 -5 - 0.5 -5 0.5 5 - 0.5 -5 0.5 5 - 0.5 -5 0.5 5 A 0.5 5 SPECIFICATIONS FOR DUAL SUPPLIES Test Conditions Unless Specified V+ = 5 V, V- = - 5 V Parameter Analog Switch Analog Signal Rangee On-Resistance On-Resistance Match Dynamic Characteristics Turn-On Timee Turn-Off Timee Break-Before-Makee Time Delay Charge Injectione tON tOFF tD Q RL = 300 , CL = 35 pF VS = 3 V, See Figure 2 DG451 only, VS = 3 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF Room Full Room Full Room Full Full 170 66 98 8 pC 200 296 96 124 200 256 96 113 ns VANALOG RON RON V+ = + 5 V, V- = - 5 V IS = - 10 mA, VD = - 3.5 V to + 3.5 V V+ = + 5 V, V- = - 5 V, IS = - 10 mA, VD = 3.5 V Full Room Full Room Full 3.8 0.13 -5 5 11 15 0.5 1 -5 5 11 12 0.5 0.5 V Symbol VL = 5 V, VIN = 2.4 V, 0.8 Va Temp.b Typ.c - 40 to 125 C Min.d Max.d - 40 to 85 C Min.d Max.d Unit Document Number: 74470 S-81306-Rev. D, 09-Jun-08 www.vishay.com 3 New Product DG451/DG452/DG453 Vishay Siliconix SPECIFICATIONS FOR DUAL SUPPLIES Test Conditions Unless Specified V+ = 5 V, V- = - 5 V Parameter Power Supplies Power Supply Current Negative Supply Current Logic Supply Current Ground Current I+ IVL = 5 V, VIN = 0 or 5 V IL IGND Room Full Room Full Room Full Room Full 0.001 - 0.001 0.001 - 0.001 - 0.5 -5 - 0.5 -5 - 0.5 -5 - 0.5 -5 - 0.5 -5 - 0.5 -5 - 0.5 -5 - 0.5 -5 A Symbol VL = 5 V, VIN = 2.4 V, 0.8 Va Temp.b Typ.c - 40 to 125 C Min.d Max.d - 40 to 85 C Min.d Max.d Unit SPECIFICATIONS FOR UNIPOLAR SUPPLIES Test Conditions Unless Specified V+ = 12 V, V- = 0 V VL = 5 V, VIN = 2.4 V, 0.8 Va - 40 to 125 C Temp.b Full IS = - 10 mA, VD = 0 V to + 10 V IS = - 10 mA, VD = + 10 V IS = - 10 mA, VD = 0 V, + 5 V, + 10 V Room Full Room Full Room Full Room Full Room Full Room Room Room Full VL = 5 V, VIN = 0 or 5 V Logic Supply Current Ground Current IL IGND Room Full Room Full Room Full 5.5 0.14 0.94 Typ.c Min.d Max.d 12 8.1 12.4 0.5 1 1.5 1.7 162 238 91 117 - 40 to 85 C Min.d Max.d 12 8.1 10.4 0.5 0.5 1.5 1.5 162 210 91 105 ns Unit V Parameter Analog Switch Analog Signal Rangee On-Resistance On-Resistance Match On-Resistance Flatness Dynamic Characteristics Turn-On Time Turn-Off Time Break-Before-Make Time Delay Charge Injection e Symbol VANALOG RON RON RFLATNESS tON tOFF tD Q RL = 300 , CL = 35 pF VS = 8 V, See Figure 2 DG453 only, VS = 8 V RL = 300 , CL = 35 pF Vg = 0 V, Rg = 0 , CL = 1 nF 132 61 70 1 0.001 - 0.001 0.001 - 0.001 - 0.5 -5 - 0.5 -5 pC 0.5 5 - 0.5 -5 0.5 5 - 0.5 -5 0.5 5 0.5 5 A Power Supplies Power Supply Current Negative Supply Current I+ I- Notes: a. VIN = input voltage to perform proper function. b. Room = 25 C, Full = as determined by the operating temperature suffix. c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. e. Guaranteed by design, not subject to production test. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. www.vishay.com 4 Document Number: 74470 S-81306-Rev. D, 09-Jun-08 New Product DG451/DG452/DG453 Vishay Siliconix TYPICAL CHARACTERISTICS 25 C, VL = 5 V, unless otherwise noted 8 7 5.0 V RON - On-Resistance () 6 10 V 5 8V 4 20 V 3 2 1 - 20 0 - 15 - 10 -5 0 5 10 15 20 0 4 8 12 16 20 24 28 32 36 VCOM - Analog Voltage (V) VCOM - Analog Voltage (V) 12 V 13.5 V 15 V TA = + 25 C IS = 10 mA RON - On-Resistance () 15 V+ = 5 V 10 V+ = 8 V V+ = 10.8 V V+ = 12 V V+ = 15 V 5 V+ = 20 V V+ = 36 V 20 TA = + 25 C IS = 10 mA On-Resistance vs. VD and Dual Supply Voltage 10 9 8 RON - On-Resistance () RON - On-Resistance () 7 6 5 + 85 C 4 3 2 1 0 - 15 - 10 -5 0 5 10 15 + 25 C - 40 C + 125 C V+ = + 15 V V- = - 15 V IS = 10 mA 12 11 10 9 8 7 6 5 4 3 2 On-Resistance vs. VD and Single Supply Voltage V+ = + 12 V V- = 0 V IS = 10 mA + 125 C + 85 C + 25 C - 40 C 0 2 4 6 8 10 12 VCOM - Analog Voltage (V) VD - Analog Voltage (V) On-Resistance vs. VD and Temperature 10 000 ID (off) 10 000 Leakage Current (pA) 1000 Leakage Current (pA) 1000 100 000 On-Resistance vs. VD and Temperature ID (off) 100 ID (on) IS (off) 10 100 ID (on) 10 IS (off) V+ = + 15 V V- = - 15 V V+ = + 13.2 V V- = 0 V 140 1 - 60 - 40 - 20 1 - 60 - 40 - 20 0 20 40 60 80 100 120 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Leakage Current vs. Temperature Leakage Current vs. Temperature Document Number: 74470 S-81306-Rev. D, 09-Jun-08 www.vishay.com 5 New Product DG451/DG452/DG453 Vishay Siliconix TYPICAL CHARACTERISTICS 25 C, VL = 5 V, unless otherwise noted 140 120 100 Q - Charge Injection (pC) 80 60 40 20 0 - 20 - 40 - 60 - 20 V+ = + 12 V V- = - 0 V tON/tOFF (ns) V+ = + 5 V V- = - 5 V CL =1 nF Drain V+ = + 15 V V- = - 15 V 275 250 225 200 175 150 125 100 75 50 15 20 25 - 55 - 35 - 15 5 25 45 65 85 105 125 tON V = 15 V tOFF V = 5 V tOFF V = 15 V tON V = 5 V - 15 - 10 -5 0 5 10 Analog Voltage (V) Temperature (C) Charge Injection vs. Analog Voltage 200 180 160 250 140 tON/tOFF (ns) tON/tOFF (ns) 120 100 80 60 40 20 4 6 8 10 12 14 16 18 20 Dual Supply Voltage (V) 50 0 - 55 tOFF tON 200 150 100 T = 25 C 350 300 Switching Time vs. Temperature and Dual Supply Voltage tON V = + 12 V tOFF V = + 12 V - 35 - 15 5 25 45 65 85 105 125 Temperature (C) Switching Time vs. Dual Supply Voltage 350 300 V T - Switching Threshold (V) T = 25 C 250 tON/tOFF (ns) 200 150 tON 100 tOFF 50 0 5 10 15 20 25 30 35 40 Single Supply Voltage (V) 3.0 Switching Time vs. Temperature and Single Supply Voltage 2.5 with VL = 5 V 2.0 1.5 1.0 0.5 0.0 0 5 10 15 20 25 30 35 40 Supply Voltage (V) Switching Time vs. Single Supply Voltage www.vishay.com 6 Switching Threshold vs. Supply Voltage Document Number: 74470 S-81306-Rev. D, 09-Jun-08 New Product DG451/DG452/DG453 Vishay Siliconix TYPICAL CHARACTERISTICS 25 C, VL = 5 V, unless otherwise noted 100 m 10 m 1m Supply Current (A) 100 10 1 100 n 10 n 1n 10 100 1k 10 k 100 k 1M 10 M IIL I+ IGND Loss, OIRR, X Talk (dB) 10 DG451/DG452/DG453 V+ = + 15 V V- = - 15 V 0 - 10 - 20 - 30 - 40 - 50 - 60 - 70 - 80 - 90 - 100 - 110 100 k 1M 10 M Frequency (Hz) V+ = + 15 V V- = - 15 V R L = 50 100 M 1G OIRR XTalk Loss Input Switching Frequency (Hz) Supply Current vs. Input Switching Frequency Insertion Loss, Off-Isolation, Crosstalk vs. Frequency TEST CIRCUITS +5V + 15 V Logic Input 3V 50 % 0V VL 10 V S IN GND VRL 300 CL 35 pF 0V tON - 15 V Note: CL (includes fixture and stray capacitance) VO = V S RL RL + R DS(on) Logic input waveform is inverted for switches that have the opposite logic sense control V+ D VO Switch Input* VS VO tOFF tr < 5 ns tf < 5 ns 90 % 90 % Figure 1. Switching Time +5V + 15 V Logic Input VL VS1 VS2 S1 IN1 S2 IN2 GND VD2 VO2 Switch Output RL1 300 RL2 300 CL2 35 pF CL1 35 pF Switch Output 0V VS2 VO2 0V V+ D1 VO1 3V 50 % 0V VS1 VO1 90 % 90 % tD tD - 15 V CL (includes fixture and stray capacitance) Figure 2. Break-Before-Make (DG453) Document Number: 74470 S-81306-Rev. D, 09-Jun-08 www.vishay.com 7 New Product DG451/DG452/DG453 Vishay Siliconix TEST CIRCUITS VO +5V + 15 V VO INX OFF VO CL 1 nF VINX OFF ON Q = VO x CL OFF ON OFF Rg VL S IN V+ D Vg 3V GND - 15 V Figure 3. Charge Injection +5V C VL VS Rg = 50 0 V, 2.4 V S2 NC IN2 GND VO VS - 15 V VC RL D2 VO S1 IN1 V+ D1 50 + 15 V C 0 V, 2.4 V XTALK Isolation = 20 log C = RF bypass Figure 4. Crosstalk +5V C VL VS Rg = 50 0 V, 2.4 V IN RL 50 GND VC 0 V, 2.4 V D - 15 V GND Off Isolation = 20 log C = RF Bypass VO VS - 15 V VC IN S V+ + 15 V C C VL V+ +5V + 15 V C D VO S Meter HP4192A Impedance Analyzer or Equivalent Figure 5. Off-Isolation Figure 6. Source/Drain Capacitances Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see http://www.vishay.com/ppg?74470. www.vishay.com 8 Document Number: 74470 S-81306-Rev. D, 09-Jun-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1 |
Price & Availability of DG451EQ-T1-E3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |